From: Griffith, Mike [MGriffith@majortool.com]
Sent: Friday, May 18, 2007 3:54 PM
To: Thomas G. Brown
Subject: FW: Need some help in finding some C6 data.

Attachments: C6 missing data R1.ppt; C6_IGES.IGS; C6 FIDUCIALS_CAD.IGS



Mike Griffith
Major Tool and Machine, Inc
Quality Control Manager
Tel: (317) 917-2612
Email: mgriffith@majortool.com

-----Original Message-----
From: Griffith, Mike 
Sent: Friday, May 18, 2007 10:06 AM
To: 'Thomas G. Brown'
Cc: Phil Heitzenroeder; 'NKHFlowen@aol.com'; 'RoyJRATC@aol.com'
Subject: FW: Need some help in finding some C6 data.

Tom,
I added a slide number 7 to your file.  This includes a cut from the MetalTek scan showing that this area is minus material.  I also had the CMM operator look into the data for this area.  Apparently some points had been filtered out during the Verisurf analysis.  I have attached IGS and verisurf files showing the data but there still are only a few points.  I believe that we have enough data to show that there is a correlation between the scan and the points we did take on the part.  This data shows that the part is in fact minus stock in this area.

Mike Griffith
Major Tool and Machine, Inc
Quality Control Manager
Tel: (317) 917-2612
Email: mgriffith@majortool.com

-----Original Message-----
From: Thomas G. Brown [mailto:tbrown@pppl.gov] 
Sent: Friday, May 18, 2007 8:20 AM
To: Griffith, Mike
Subject: RE: Need some help in finding some C6 data.

Sorry Mike, here's the updated slides.......... Tom

-----Original Message-----
From: Griffith, Mike [mailto:MGriffith@majortool.com] 
Sent: Thursday, May 17, 2007 9:33 PM
To: Thomas G. Brown
Cc: Phil Heitzenroeder
Subject: RE: Need some help in finding some C6 data.

Tom,
Please send me the slide you are referring to.  There was no attachment in
your last email.

Mike Griffith
Major Tool and Machine, Inc
Quality Control Manager
Tel: (317) 917-2612
Email: mgriffith@majortool.com
-----Original Message-----
From: Thomas G. Brown [mailto:tbrown@pppl.gov] 
Sent: Thursday, May 17, 2007 9:59 AM
To: Griffith, Mike
Cc: Phil Heitzenroeder
Subject: RE: Need some help in finding some C6 data.

Sorry Mike the data is still missing.  I pulled in the IGES file and although
there are some points on the surface in question there are far too few.  I
added slides 4, 5 and 6 to my earlier view graphs.  I pulled in the file of
the as cast data and there was no points in the where I was looking for them;
however I did see some excess material near a bolt spot face region (slide
5).  I assume that the spot face is deep enough to take care of the excess
material.   I also wanted to have you check on a local chamber that we added
some time ago to make sure it was there (slide 6).  

Tom
   

-----Original Message-----
From: Griffith, Mike [mailto:MGriffith@majortool.com] 
Sent: Wednesday, May 16, 2007 4:21 PM
To: Thomas G. Brown
Cc: Phil Heitzenroeder
Subject: RE: Need some help in finding some C6 data.

Tom,
I have not verified this yet but I believe the data would be in the inside As
Cast reports.  This should also be in the IGS data.  If you have not found it
I can investigate further tomorrow.

Mike Griffith
Major Tool and Machine, Inc
Quality Control Manager
Tel: (317) 917-2612
Email: mgriffith@majortool.com

-----Original Message-----
From: Thomas G. Brown [mailto:tbrown@pppl.gov] 
Sent: Wednesday, May 16, 2007 9:51 AM
To: Griffith, Mike
Cc: Phil Heitzenroeder
Subject: Need some help in finding some C6 data.

Hi Mike,

I've started to go through the C6 involving the wing interfaces and could not
find the complete data on the inside wing D side.  I've attaché a PPT file
that shows what I've found.  There appears to be data missing.  I've looked
at all the files but still can't find the missing points.  

Tom