Database: NCSX PUNCHLIST.fp7
Records: 593
Task No.	Item	Ref.	Description	Work Status	Update	FPA	Status
T-050	Coil B-6	ECN 5140	Cut fingers of top chill plates	In-Progress		Yes	OPEN
T-058	Coil B-6	ECN 5140	Replace chill plates in lead and poloidal break areas with G-11 spacers	In-Progress		Yes	OPEN
T-066	Coil B-6	ECN 5140	In power bus tie in area- Install Kapton insulation over bolt to mitigate potentially short tracking path	In-Progress		No	OPEN
T-084	Coil B-6	ECN 5140	Install insulating washers on one side of the power bus connection to eliminate floating hardware [4]	Not Started		No	OPEN
T-092	Coil B-6	ECN 5140	Install a Kapton or thin G-11 sheet underneath the jumper stack to increase the tracking distance	In-Progress		Yes	OPEN
T-100	Coil B-6	ECN 5140	Install insulating plugs at bottom of the hole in the G-11 base plate to reduce the risk of the studs penetrating the G-11 backing plate	In-Progress		Yes	OPEN
T-118	Coil B-6	ECN 5140	Electrically tie the three jumper studs to the bottom jumper	Not Started		No	OPEN
T-136	Coil B-6	ECN 5140	Cover entire lead area with cover/box	Not Started		No	OPEN
T-177	Coil B-6		Terminate cooling lines- braze fitting to tubes/ fill tube penetration holes	Not Started		No	OPEN
T-195	Coil B-6		Install strain gauges- fiber optic	Not Started	Need design/Materials - awaiting Oak Ridge to finalize	Yes	OPEN
T-213	Coil B-6		Install thermocouples (coil areas)	Not Started		Yes	OPEN
T-231	Coil B-6	NCR 3634/3639	Modify final coil clamps- permeability & fitup issues	Not Started		Yes	OPEN
T-249	Coil B-6		Lock all clamp hardware- weld locking wire	In-Progress		Yes	OPEN
T-267	Coil B-6		Mount final co-wound diagnostic box to casting	In-Progress		Yes	OPEN
T-285	Coil B-6		Documentation package complete and ready for copy	In-Progress		Yes	OPEN
T-337	Coil B-6		Metrology (pre-measurement)	Not Started		Yes	OPEN
T-355	Coil B-6		Grind overcasting	Not Started	Grind additional areas noted in B1-C1 gross fit	Yes	OPEN
T-391	Coil B-6		Grinding/milling to accommodate nut access	In-Progress		Yes	OPEN
T-409	Coil B-6		Check thread engagement on tapped holes	Not Started		Yes	OPEN
T-427	Coil B-6		Check threads (run bolt through) on tapped holes	Not Started		Yes	OPEN
T-475	Coil B-6		Correct clamp interference (#60, 69)	Not Started		Yes	OPEN
T-495	Coil B-6		Complete electrical tests following VPI	Not Started		Yes	OPEN
T-507	Coil B-6		Install batt insulation	Not Started		Yes	OPEN
T-544	Coil B-6		Fabricate Bushings	In-Progress		Yes	OPEN
T-562	Coil B-6		Remove epoxy overflow fittings	Not Started		Yes	OPEN
T-572	Coil B-6		Secure terminal lug hardware	Not Started		No	OPEN
T-587	Coil B-6		Electrical test (7.5 kV) following winding form re-work	Not Started		Yes	OPEN
FileMaker Pro Version: 8.0v3
Build: 03-20-2006