|
RFD Number |
Associated ECP Number |
Title |
Date Approved or
Disapproved |
RFD Status |
| |
|
|
|
|
|
14-009 |
038 |
Proposed Drawing
Changes |
10/18/2005 |
Approved. CSPEC and
Drawings to be updated by Oct 31st. |
|
14-008 |
TBD |
C1 ONLY – Add
Additional G11CR Shim Pieces for the Poloidal Break |
9/22/2005 |
Approved. CSPEC and
Drawings will
be updated by Oct 31st. |
|
14-007 |
TBD |
Modular Coil Jumper
Material Substitution |
9/30/2005 |
Approved. CSPEC and
Drawings will
be updated by Oct 31st. |
|
14-006 |
TBD |
Deletion of Erroneous
Requirement in Section 3.1.1.6.1 of the Modular Coil CSPEC
(NCSX-CSPEC-141-03) |
9/15/2005 |
Approved. CSPEC will
be updated by Oct 31st. |
|
14-005 |
|
For C1 only -Waiver
of Post Machining Inspection for Internal Defects in High Stress
Area & Radiography on Weld Repair |
9/15/2005 |
Approved. |
|
12-007 |
N/A |
NCSX Vessel Port
Pre-Assembly and Blank-Off for Vacuum Testing |
8/22/2005 |
Disapproved - leak
checking ok, but PPPL needs all the blank off flanges for testing at
PPPL. |
|
14-004 |
N/A |
Add fillets to
Modular Coil Lower Lead Blocks to Aid Machining |
7/25/2005 |
Approved with caveat
that mating parts be chamfered to clear added fillets. |
|
14-003 |
033 |
Relaxation of
Material Testing Requirements |
6/8/2005 |
Authorizes deviation
to not require testing in transverse and longitudinal directions. |
|
12-006 |
032 |
NCSX Vessel Port
Manufacture |
5/27/2005 |
Authorization to
manufacture 2.5" pipe and 3.5" pipe from ASTM 625 plate. |
|
12-005 |
N/A |
NCSX Vessel Port
Manufacture |
5/18/2005 |
DISAPPROVED
-
Search for more Sch40 pipe - Project will evaluate Sch10 splicing
strategy. |
|
14-002 |
N/A |
Change in Dimensional
Inspection Requirements for the C1 Casting |
4/15/2005 |
Deleted requirement for second dimensional inspection => deemed
redundant. |
|
12-004 |
N/A |
VVSA Leak Check
Tube/Block Weld |
4/4/2005 |
It is permissible to
replace the weld with a braze joint using a silver free braze
material (Nicrobraz). |
|
12-003 |
N/A |
VVSA Tube Clip
Thickness |
4/4/2005 |
The use of any gauge
in the range of 0.01 to 0.02 will be acceptable to the Laboratory
provided it is Inconel 625 alloy, and is found to perform adequately
by the vendor. |
|
14-001 |
028 |
RFD-14-001, Revised
Location of Part Number in MCWF Casting |
3/30/2005 |
Drawing
SE-141-114 shows the reference location of the pattern/casting
identification number for Type A coils. No change in that drawing is
planned, at least not until all of the Type A coils are fabricated. |
|
12-002R1 |
027 |
RFD-12-002,
Substitution of Schedule 10 for Schedule 40 Piping |
3/24/2005 |
Incorporated in Rev 5
of NCSX-CSPEC-121-02 |
|
12-001 |
025 |
RFD-12-001 - Approval
to use ASTM B705 and ASTM B443 for Manufacture of Piping from Plate |
3/10/2005 |
Incorporated in Rev 5
of NCSX-CSPEC-121-02 |
